[BACK]Return to INSTALL CVS log [TXT] [DIR] Up to [parser3project] / parser3

Diff for /parser3/INSTALL between versions 1.22 and 1.40

version 1.22, 2002/06/20 13:39:56 version 1.40, 2005/03/16 14:37:03
Line 1 Line 1
 0.Assuming your perform your builds in $D directory   0.Assuming your perform your builds in $HOME directory 
   and suggested subdirectories.    and suggested subdirectories.
   
 1.What is the process to compile Parser3?   1.What is the process to compile Parser3?
   
     First, you must have LIBGC installed (conservative garbage collector for C++).
         libgc >= 6.1 [http://www.hpl.hp.com/personal/Hans_Boehm/gc/gc_source/gc6.4.tar.gz]
       
       Installation sequence of this library to $HOME/gc:
   
       cd libgc-x.x
       ./configure --prefix=$HOME/gc --disable-threads --silent
       make install
   
       Then you can use these Parser3 configure options to specify the location and static/dynamic linkage with libgc:
           --with-static-gc=$HOME/gc/lib
           --with-shared-gc=$HOME/gc/lib
   
       NOTE:
       On some platforms there is special version of libgc patched to support some
       local piece of subtlety.
       Official libgc does not work there, use special version instead.
       (OpenBSD reported to be one of those)
   
   As most UNIX programs Parser3 follows the "standard":    As most UNIX programs Parser3 follows the "standard":
   
   mkdir $D/parser3project    mkdir $HOME/parser3project
   cd $D/parser3project    cd $HOME/parser3project
   gunzip -c parser3-x.x.tar.gz | tar xvf -    gunzip -c parser3-x.x.tar.gz | tar xvf -
   mv parser3-x.x parser3    mv parser3-x.x parser3
   cd parser3    cd parser3
   ./configure --prefix=/usr/local    ./configure --prefix=$HOME/parser3install --silent
   make    make
       
   That renaming is needed for SQL drivers to be able to find     That renaming is needed for SQL drivers to be able to find 
Line 45 Line 64
   
 3.What other libraries are needed to compile/install parser?   3.What other libraries are needed to compile/install parser? 
   
   * You can compile and use parser without any additional libraries.  3a. In case you wish XML(xdoc and xnode classes) support, you need libraries
     That would be 'basic' version of it.        libxml2 >= 2.6.5 [ftp://xmlsoft.org/libxml2-2.6.17.tar.gz]
         libxslt >= 1.1.2 [ftp://xmlsoft.org/libxslt-1.1.10.tar.gz]
         glib >= 1.2.10 [ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz] 
   * In case you wish xml(xdoc and xnode classes) support you need libraries        on freebsd5 this is reported to work: ftp://ftp.gtk.org/pub/gtk/v1.1/glib-1.1.16.tar.gz
       libxml2 >= 2.4.11        gdome2 >= 0.7.4 [http://gdome2.cs.unibo.it/tarball/gdome2-0.8.1.tar.gz]
       libxslt >= 1.0.9  
       glib >= 1.2.10  
       gdome2 >= 0.7.0  
     on your system, and specify path to them to Parser3 configure script.      on your system, and specify path to them to Parser3 configure script.
   
     Sources of these two libraries must be patched prior to compile:       Sources of libgdome library must be patched prior to compile. [library author bug confirmation pending]
       * libxml2  
       * libxslt  
   
     Installation sequence of these libraries to $D/gnome:      Installation sequence of these libraries to $HOME/gnome:
   
     libxml2:  [ftp://ftp.gnome.org/pub/GNOME/stable/sources/libxml/libxml2-2.4.12.tar.gz]      libxml2:
   
     cd libxml2-x.x.x      cd libxml2-x.x.x
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_error_column_tab.patch      ./configure --prefix=$HOME/gnome --without-zlib --without-iconv --without-threads --silent
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_htmloutput_of_xslemptyattr_emptyquotes.patch  
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_transcoder_context1.patch  
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_transcoder_context2.patch  
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_transcoder_context3.patch  
     patch -p0 < $D/parser3project/parser3/src/patches/libxml_transcoder_context4.patch  
     ./configure --prefix=$D/gnome --without-zlib  
     make install      make install
   
     libxslt:  [ftp://ftp.gnome.org/pub/GNOME/stable/sources/libxslt/libxslt-1.0.9.tar.gz]      libxslt:
   
     cd libxslt-x.x.x      cd libxslt-x.x.x
     patch -p0 < $D/parser3project/parser3/src/patches/libxslt_html_output_no_charset_meta.patch      ./configure --with-libxml-prefix=$HOME/gnome --prefix=$HOME/gnome --without-debug --without-debugger --silent
     ./configure --with-libxml-prefix=$D/gnome --prefix=$D/gnome --without-debug --without-debugger  
     make install      make install
   
     glib:  [ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz]      glib:
   
     cd glib-x.x.x      cd glib-x.x.x
     ./configure --prefix=$D/gnome       ./configure --prefix=$HOME/gnome --silent
     make install      make install
   
     gdome2:  [http://phd.cs.unibo.it/gdome2/tarball/gdome2-0.7.0.tar.gz]      gdome2:
   
     cd gdome2-x.x.x      cd gdome2-x.x.x
         patch -p0 < $D/parser3project/parser3/src/patches/libgdome_cpp_syntax1.patch      patch -p0 < $HOME/parser3project/parser3/src/lib/patches/gdome2.patch
         patch -p0 < $D/parser3project/parser3/src/patches/libgdome_cpp_syntax2.patch      ./configure --with-glib-prefix=$HOME/gnome --disable-glibtest --with-libxml-prefix=$HOME/gnome --prefix=$HOME/gnome --silent
         patch -p0 < $D/parser3project/parser3/src/patches/libgdome_morestatic.patch  
     ./configure --with-glib-prefix=$D/gnome --disable-glibtest --with-libxml-prefix=$D/gnome --prefix=$D/gnome  
     make install      make install
   
     And copy these additional headers into install includes directory      And copy these additional headers into install includes directory
   
     mkdir $D/gnome/include/libgdome/gdomecore      mkdir -p $HOME/gnome/include/libgdome/gdomecore
     cp libgdome/gdomecore/gdome-xml-node.h $D/gnome/include/libgdome/gdomecore      cp libgdome/gdomecore/gdome-xml-node.h $HOME/gnome/include/libgdome/gdomecore
     cp libgdome/gdomecore/gdome-xml-document.h $D/gnome/include/libgdome/gdomecore      cp libgdome/gdomecore/gdome-xml-document.h $HOME/gnome/include/libgdome/gdomecore
           
   
     Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:      Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:
         --with-static-xml=$D/gnome          --with-static-xml=$HOME/gnome
         --with-shared-xml=$D/gnome          --with-shared-xml=$HOME/gnome
   
       NOTE:
       In case your glib as installed into some other prefix,
       specify it's configuration file with
           --with-glib-config=/path/to/your/glib-config
       NOTE:
       In case you are using SHARED xml libraries, you may want to link in direct path to them,
       use this key to specify which linker key to use do do that:
           --with-pathlink=LKEY    put dynamic libraries paths to binary
                                   using linker key (-R, -rpath-link)
   
   3b. In case you wish $mail:receive support you need libraries
         glib >= 1.2.10 [ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz]
         gmime >= 1.0.1 [http://spruce.sourceforge.net/gmime/sources/v1.0/gmime-1.0.8.tar.gz]
       on your system, and specify path to them to Parser3 configure script.
   
       You may have already installed glib at 3b step.
   
       glib:
   
       cd glib-x.x.x
       ./configure --prefix=$HOME/gnome 
       make install
   
       gmime:
   
       cd gmime-x.x.x
       ./configure --prefix=$HOME/gnome
       make install
   
       Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:
           --with-static-mailreceive=$HOME/gnome
           --with-shared-mailreceive=$HOME/gnome
   
     NOTE:      NOTE:
     In case your glib as installed into some other prefix,      In case your glib as installed into some other prefix,
     specify it's configuration file with      specify it's configuration file with
         --with-glib-config=/path/to/your/glib-config          --with-glib-config=/path/to/your/glib-config
         NOTE:      NOTE:
         In case you are using SHARED xml libraries, you may want to link in direct path to them,      In case you are using SHARED mime library, you may want to link in direct path to it,
     use this key to specify which linker key to use do do that:      use this key to specify which linker key to use do do that:
         --with-pathlink=LKEY    put dynamic libraries paths to binary          --with-pathlink=LKEY    put dynamic libraries paths to binary
                                 using linker key (-R, -rpath-link)                                  using linker key (-R, -rpath-link)
Line 125 Line 163
   and afterwards copy parser3install/bin/parser3 to your CGI directory    and afterwards copy parser3install/bin/parser3 to your CGI directory
   or make a symlink [if your web server configured to follow symlinks].    or make a symlink [if your web server configured to follow symlinks].
   
   You can disable libstdc++ linkage by setting  
   --disable-link-libstdcpp  
   option to configure.    
   
   You can disable any exec operations by setting    You can disable any exec operations by setting
   --disable-execs    --disable-execs
   option to configure.    option to configure.
   file::exec, file::cgi and mail:send (unix version) methods would be disabled.    file::exec, file::cgi and mail:send (unix version) methods would be disabled.
   
   You can disable reading and executing files, belonging to group     You can enable reading and executing files, not belonging to group+user 
   other then current by setting    other then effective by setting
   --disable-foreign-group-files    --disable-safe-mode
   option to configure.    option to configure.
       
   You can disable user-configured sendmail commands by forcing it, setting    You can disable user-configured sendmail commands by forcing it, setting
   "--with=sendmail=COMMAND"    "--with=sendmail=COMMAND"
   option to configure.    option to configure.
     
     In case you are experiencing problem with gcc runtime exception handling,
     try to configure with
     --with-sjlj-exceptions
     option.  
   
     By default libstdc++ is linked statically, you can re-enable dynamic libstdc++ linkage by specifying
     --with-dynamic-stdcpp
     option to configure.  
   
   
   Some root config options can be specified at configure time, and would override autodetects.    Some root config options can be specified at configure time, and would override autodetects.
   
Line 154 Line 197
   --with-pgsql-client=pgsqlclientlib?params    --with-pgsql-client=pgsqlclientlib?params
   --with-oracle-client=oracleclientlib?params    --with-oracle-client=oracleclientlib?params
       
    5.
     If you need to build apache 1.3 parser module, get source distribution of apache 1.3,
     run configure there, then run parser configure with one more option:
     --with-apache13=Apache13 source distribution directory
     after 'make' go to that directory and run
   
     ./p3runConfigure <any additional options to apache configure to pass>
     
     example:
     ./p3runConfigure --prefix=$D/apache13install --enable-module=rewrite
   
     WARNING: if you want to use apache configure option --enable-shared=max, do this:
     ./p3runConfigure --enable-shared=max --disable-shared=mod_parser3.c
     
 Alexandr Petrosian <paf@design.ru> (http://paf.design.ru)  Alexandr Petrosian <paf@design.ru> (http://paf.design.ru)
   
 $Id$  $Id$
Removed from v.1.22  
changed lines
  Added in v.1.40

E-mail: