[BACK]Return to INSTALL CVS log [TXT] [DIR] Up to [parser3project] / parser3

Diff for /parser3/INSTALL between versions 1.26 and 1.41

version 1.26, 2002/09/04 14:59:54 version 1.41, 2005/11/30 14:56:58
Line 1 Line 1
 0.Assuming your perform your builds in $D directory   0.Assuming your perform your builds in $HOME directory 
   and suggested subdirectories.    and suggested subdirectories.
   
 1.What is the process to compile Parser3?   1.What is the process to compile Parser3?
   
     First, you must have LIBGC installed (conservative garbage collector for C++).
         libgc >= 6.6
       
       Installation sequence of this library:
   
           mkdir $HOME/p3p/src
           cd $HOME/p3p/src
           wget http://www.hpl.hp.com/personal/Hans_Boehm/gc/gc_source/gc6.6.tar.gz
           gunzip -c gc6.6.tar.gz | tar vxf -
       cd gc6.6
       ./configure --prefix=$HOME/p3p/gc --disable-threads --silent
       make install
   
       Then you can use these Parser3 configure options to specify the location and static/dynamic linkage with libgc:
           --with-static-gc=$HOME/p3p/gc/lib
           --with-shared-gc=$HOME/p3p/gc/lib
   
       NOTE:
       On some platforms there is special version of libgc patched to support some
       local piece of subtlety.
       Official libgc does not work there, use special version instead.
       (OpenBSD reported to be one of those)
   
   As most UNIX programs Parser3 follows the "standard":    As most UNIX programs Parser3 follows the "standard":
   
   mkdir $D/parser3project    mkdir $HOME/p3p
   cd $D/parser3project    cd $HOME/p3p
   gunzip -c parser3-x.x.tar.gz | tar xvf -    gunzip -c parser3-x.x.tar.gz | tar xvf -
   mv parser3-x.x parser3    mv parser3-x.x parser3
   cd parser3    cd parser3
   ./configure --prefix=/usr/local    ./configure --prefix=$HOME/parser3install --silent
   make    make
       
   That renaming is needed for SQL drivers to be able to find     That renaming is needed for SQL drivers to be able to find 
Line 45 Line 68
   
 3.What other libraries are needed to compile/install parser?   3.What other libraries are needed to compile/install parser? 
   
 3a. You can compile and use parser without any additional libraries.  3a. In case you wish XML(xdoc and xnode classes) support, you need libraries
     That would be 'basic' version of it.        libxml2 >= 2.6.22
         libxslt >= 1.1.15
 3b. In case you wish xml(xdoc and xnode classes) support you need libraries        glib >= 1.2.10 
       libxml2 >= 2.4.11        gdome2 >= 0.8.1
       libxslt >= 1.0.9  
       glib >= 1.2.10  
       gdome2 >= 0.7.0  
     on your system, and specify path to them to Parser3 configure script.      on your system, and specify path to them to Parser3 configure script.
   
     Sources of these two libraries must be patched prior to compile:       Sources of libgdome library must be patched prior to compile. [library author bug confirmation pending]
       * libxml2  
       * libxslt  
   
     Installation sequence of these libraries to $D/gnome:      Installation sequence of these libraries to $HOME/p3p/gnome:
   
     libxml2:  [ftp://ftp.gnome.org/pub/GNOME/stable/sources/libxml/libxml2-2.4.12.tar.gz]      libxml2:
   
     cd libxml2-x.x.x          cd $HOME/p3p/src
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_error_column_tab.patch          wget ftp://xmlsoft.org/libxml2-2.6.22.tar.gz
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_htmloutput_of_xslemptyattr_emptyquotes.patch          gunzip -c libxml2-2.6.22.tar.gz | tar vxf -
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_transcoder_context1.patch      cd libxml2-2.6.22
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_transcoder_context2.patch      ./configure --prefix=$HOME/p3p/gnome --without-zlib --without-iconv --without-threads --silent
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_transcoder_context3.patch  
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxml_transcoder_context4.patch  
     ./configure --prefix=$D/gnome --without-zlib  
     make install      make install
   
     libxslt:  [ftp://ftp.gnome.org/pub/GNOME/stable/sources/libxslt/libxslt-1.0.9.tar.gz]      libxslt:
   
     cd libxslt-x.x.x          cd $HOME/p3p/src
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libxslt_html_output_no_charset_meta.patch          wget ftp://xmlsoft.org/libxslt-1.1.15.tar.gz
     ./configure --with-libxml-prefix=$D/gnome --prefix=$D/gnome --without-debug --without-debugger          gunzip -c libxslt-1.1.15.tar.gz | tar vxf -
       cd libxslt-1.1.15
       ./configure --with-libxml-prefix=$HOME/p3p/gnome --prefix=$HOME/p3p/gnome --without-debug --without-debugger --silent
     make install      make install
   
     glib:  [ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz]      glib:
   
     cd glib-x.x.x          cd $HOME/p3p/src
     ./configure --prefix=$D/gnome       #on freebsd5 this is reported to work: ftp://ftp.gtk.org/pub/gtk/v1.1/glib-1.1.16.tar.gz
       wget ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz
           gunzip -c glib-1.2.10.tar.gz | tar vxf -
       cd glib-1.2.10
       ./configure --prefix=$HOME/p3p/gnome --silent
     make install      make install
   
     gdome2:  [http://phd.cs.unibo.it/gdome2/tarball/gdome2-0.7.0.tar.gz]      gdome2:
   
     cd gdome2-x.x.x          cd $HOME/p3p/src
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libgdome_cpp_syntax1.patch      wget http://gdome2.cs.unibo.it/tarball/gdome2-0.8.1.tar.gz
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libgdome_cpp_syntax2.patch          gunzip -c gdome2-0.8.1.tar.gz | tar vxf -
     patch -p0 < $D/parser3project/parser3/src/lib/patches/libgdome_morestatic.patch      cd gdome2-0.8.1
     ./configure --with-glib-prefix=$D/gnome --disable-glibtest --with-libxml-prefix=$D/gnome --prefix=$D/gnome      patch -p0 < $HOME/p3p/parser3/src/lib/patches/gdome2.patch
       ./configure --with-glib-prefix=$HOME/p3p/gnome --disable-glibtest --with-libxml-prefix=$HOME/p3p/gnome --prefix=$HOME/p3p/gnome --silent
     make install      make install
   
     And copy these additional headers into install includes directory      And copy these additional headers into install includes directory
   
     mkdir $D/gnome/include/libgdome/gdomecore      mkdir -p $HOME/p3p/gnome/include/libgdome/gdomecore
     cp libgdome/gdomecore/gdome-xml-node.h $D/gnome/include/libgdome/gdomecore      cp libgdome/gdomecore/gdome-xml-node.h $HOME/p3p/gnome/include/libgdome/gdomecore
     cp libgdome/gdomecore/gdome-xml-document.h $D/gnome/include/libgdome/gdomecore      cp libgdome/gdomecore/gdome-xml-document.h $HOME/p3p/gnome/include/libgdome/gdomecore
           
   
     Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:      Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:
         --with-static-xml=$D/gnome          --with-static-xml=$HOME/p3p/gnome
         --with-shared-xml=$D/gnome          --with-shared-xml=$HOME/p3p/gnome
   
     NOTE:      NOTE:
     In case your glib as installed into some other prefix,      In case your glib as installed into some other prefix,
Line 116 Line 138
         --with-pathlink=LKEY    put dynamic libraries paths to binary          --with-pathlink=LKEY    put dynamic libraries paths to binary
                                 using linker key (-R, -rpath-link)                                  using linker key (-R, -rpath-link)
   
 3c. In case you wish $mail:receive support you need libraries  3b. In case you wish $mail:receive support you need libraries
       glib >= 1.2.10        glib >= 1.2.10
       gmime >= 1.0.1        gmime >= 1.0.1 [http://spruce.sourceforge.net/gmime/sources/v1.0/gmime-1.0.8.tar.gz]
     on your system, and specify path to them to Parser3 configure script.      on your system, and specify path to them to Parser3 configure script.
   
     You may have already installed glib at 3b step.      You may have already installed glib at 3b step.
   
     glib:  [ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz]      glib:
   
     cd glib-x.x.x          cd $HOME/p3p/src
     ./configure --prefix=$D/gnome       #on freebsd5 this is reported to work: ftp://ftp.gtk.org/pub/gtk/v1.1/glib-1.1.16.tar.gz
       wget ftp://ftp.gtk.org/pub/gtk/v1.2/glib-1.2.10.tar.gz
           gunzip -c glib-1.2.10.tar.gz | tar vxf -
       cd glib-1.2.10
       ./configure --prefix=$HOME/p3p/gnome --silent
     make install      make install
   
     gmime:  [http://spruce.sourceforge.net/gmime/sources/gmime-1.0.5.tar.gz]      gmime:
   
     cd gmime-x.x.x      cd gmime-x.x.x
     ./configure --prefix=$D/gnome      ./configure --prefix=$HOME/p3p/gnome
     make install      make install
   
     Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:      Parser3 configure options, choose whether you need static or dynamic linkage with xml libs:
         --with-static-mailreceive=$D/gnome          --with-static-mailreceive=$HOME/p3p/gnome
         --with-shared-mailreceive=$D/gnome          --with-shared-mailreceive=$HOME/p3p/gnome
   
     NOTE:      NOTE:
     In case your glib as installed into some other prefix,      In case your glib as installed into some other prefix,
Line 153 Line 179
   
   In case you're not root on machine you're installing Parser,    In case you're not root on machine you're installing Parser,
   we recommend you to do:    we recommend you to do:
   ./configure --prefix=/your/home/parser3install    ./configure --prefix=$HOME/p3i
   and afterwards copy parser3install/bin/parser3 to your CGI directory    and afterwards copy $HOME/p3i/bin/parser3 to your CGI directory
   or make a symlink [if your web server configured to follow symlinks].    or make a symlink [if your web server configured to follow symlinks].
   
   You can disable libstdc++ linkage by setting  
   --disable-link-libstdcpp  
   option to configure.    
   
   You can disable any exec operations by setting    You can disable any exec operations by setting
   --disable-execs    --disable-execs
   option to configure.    option to configure.
   file::exec, file::cgi and mail:send (unix version) methods would be disabled.    file::exec, file::cgi and mail:send (unix version) methods would be disabled.
   
   You can disable reading and executing files, belonging to group     You can enable reading and executing files, not belonging to group+user 
   other then current by setting    other then effective by setting
   --disable-foreign-group-files    --disable-safe-mode
   option to configure.    option to configure.
       
   You can disable user-configured sendmail commands by forcing it, setting    You can disable user-configured sendmail commands by forcing it, setting
   "--with=sendmail=COMMAND"    --with=sendmail="COMMAND"
   option to configure.    option to configure, for example:
     --with-sendmail="/usr/sbin/sendmail -i -t -f postmaster"
   
   In case you are experiencing problem with gcc runtime exception handling,    In case you are experiencing problem with gcc runtime exception handling,
   try to configure with    try to configure with
   --with-sjlj-exceptions    --with-sjlj-exceptions
   option.      option.  
   
     By default libstdc++ is linked statically, you can re-enable dynamic libstdc++ linkage by specifying
     --with-dynamic-stdcpp
     option to configure.  
   
   
   Some root config options can be specified at configure time, and would override autodetects.    Some root config options can be specified at configure time, and would override autodetects.
   
   List of enabled charsets:    List of enabled charsets:
Line 190 Line 218
   --with-pgsql-client=pgsqlclientlib?params    --with-pgsql-client=pgsqlclientlib?params
   --with-oracle-client=oracleclientlib?params    --with-oracle-client=oracleclientlib?params
       
    5.
     If you need to build apache 1.3 parser module, get source distribution of apache 1.3,
     run configure there, then run parser configure with one more option:
     --with-apache13=Apache13 source distribution directory
     after 'make' go to that directory and run
   
     ./p3runConfigure <any additional options to apache configure to pass>
     
     example:
     ./p3runConfigure --prefix=$D/apache13install --enable-module=rewrite
   
     WARNING: if you want to use apache configure option --enable-shared=max, do this:
     ./p3runConfigure --enable-shared=max --disable-shared=mod_parser3.c
     
 Alexandr Petrosian <paf@design.ru> (http://paf.design.ru)  Alexandr Petrosian <paf@design.ru> (http://paf.design.ru)
   
 $Id$  $Id$
Removed from v.1.26  
changed lines
  Added in v.1.41

E-mail: